Power supply circuit to generate output below were variations between 1.3V DC to 12.2V DC with 1A current.
In addition, the power supply circuit is also equipped with over-current protection or shield against belebih flow. Power supply circuit is very simple, but the quality is quite good, made her basiskan regulator IC LM723 is a pretty legendary.
Description:
R2 to set the output voltage. The maximum current is determined by R3, over-current protection circuit inside the LM723 to detect the voltage on R3, if it reaches 0.65 V, the voltage output will be off her. So the current through R3 can not exceed 0.65 / R3 although output short-circuit in his.
C3 and C4 are ceramic capacitors, as much as possible directly soldered to the PCB, this is because the LM723 is prone to oscillation that is not cool.
LM723 works with 9.5V input voltage to 40 V DC and the LM723 can generate its own current of 150mA when the output voltage is not more than 6-7V under input voltage.
Specifications:
Output (value estimated):
Vmin = (R4 + R5) / (R5 * 1.3)
Vmax = (7.15 / R5) * (R4 + R5)
Imax = 0.65/R3
Max. Power on R3: 0.42/R3
Min. DC Input Voltage (pin 12 to pin 7): Vmax + 5
Component List:
B1 40V/2.5A
C1 2200uF (3300uF even better)
C2 4.7uF
C3 100nF
C4 1NF
C5 330nF
C6 100uF
Green LED D1
D2 1N4003
F1 0.2A F
F2 2A M
IC1 LM723 (in a DIL14 plastic package)
R1 1k
R2 Pot. 5k
R3 0.56R/2W
R4 3.3k
R5 4.7k
S1 250V/1A
T1 2N3055 on a heatsink 5K / W
TR1 220V/17V/1.5
Related Posts :
Audio power amplifier circuit based on TDA4920 , TDA4925 , TDA4930Specification :This is stereo amplifier , based on IC TDA4920 , TDA4925 , TDA4930 . Minimum voltage … Read More...
Circuit Audio Amplifer with IC 5G37 Himm.,.,. I just get this schematic on my mind . This Circuit require voltage supply min… Read More...
Schematic Power Amplifier with IC AN7116 Mono Amplifier*notif : this is mono amplifier. On this schematic circuit power amplifier with IC… Read More...
Schematic Audio Power Amplifier with IC AN7105This Schematic Circuit Audio Amplifier use IC AN7105 , minimum voltage 1,5 volt and maximum voltage … Read More...
Schematic Audio Amplifier with IC AN214See this circuit below :Datasheet IC AN214Vcc … Read More...
Schematic Audio Amplifier with IC A211D / TBA611See this circuit below:Datasheet IC A211DVcc … Read More...
Schematic Audio Amplifier with IC AN5265Schematic Description :This Circuit Require voltage 12 -26 Volt. Good Voltage use is 16 Volt , Becau… Read More...
Schematic Audio Power Amplifier with IC AN7118S *notif : this circuit is stereo power amplifierAlthough the schematic power amplifier with IC … Read More...
Rangkaian amplifierTechnical informationDatasheet IC 5G37Vcc = 6… Read More...
Schematic Power Amplifier with IC AN7114 or AN7115This Circuit must use the IC AN7114 or you can use the IC AN7115 . Minimum voltage for this IC is 6 … Read More...
Schematic Audio Amplifier with IC AN7108See this circuit below:Datasheet IC AN7108Vcc … Read More...
Schematic Audio Amplifer with IC AN315This Schematic Require voltage 9 - 18 Volt. Good voltage for this schematic is 12 V. This is Mono am… Read More...
Circuit Audio Amplifer with IC TBA 611 This Circuit require voltage 4,5 to 15 Volt. I recomended to this circuit supply with 12… Read More...
Schematic Audio Amplifier with IC AN313This schematic very suitable applied on small speakers. Because the maximum output is 3W and the min… Read More...
Low noise amplifier circuit with IC TDA1037This power amplifier use IC TDA1037 or you can use TDA1037D for main operation . Minimum requi… Read More...
Schematic Audio Power Amplifier with IC AN7110 / AN7130Description Schematic :Minimum Voltage for this Circuit is 6 Volt , and Maximum voltage is 18 Volt .… Read More...
Schematic Audio Amplifier with IC AN374This Schematic use IC AN374, this is mono amplifier and have output speaker 1 W with impedance 8 Ohm… Read More...
1 W mini audio amplifier circuitIn this circuit requires only three components , namely IC TDA7052 , and 2 capacitor electrolyte. Ac… Read More...
Schematic Power Amplifier with adjusting voltagePower amplifier using IC TDA1013 , minimum require voltage 15 volt and maximum voltage 35 volt . But… Read More...
Low Voltage Amplifier Circuit with IC BA518This Circuit use IC BA518 or you can use the IC BA547 , this is low mono power amplifier. Maximum po… Read More...
0 Response to "1.3V DC to 12.2V DC Regulator Power Supply"
Post a Comment